Dynamic_Nat_Configuration

 



Download link for Practical of Dynamic_NAT_Configuration via Static:


IP Configuration on R-1:

---------------------------

Router>enable

Router#conf terminal

Router(config)#hostname R-1

R-1(config)#interface serial 1/0

R-1(config-if)#ip address 121.10.10.10 255.0.0.0

R-1(config-if)#clock rate 72000

R-1(config-if)#no shu

R-1(config-if)#exit

R-1(config)#interface fastEthernet 0/0

R-1(config-if)#ip address 10.0.0.1 255.0.0.0

R-1(config-if)#no shu

R-1(config-if)#exit


RIPv1 Routing Configuration on R-1:-

------------------------------------

R-1(config)#router rip 

R-1(config-router)#network 121.10.10.0

R-1(config-router)#network 10.0.0.0


IP Configuration on R-2:-

--------------------------

Router(config)#hostname R-2

R-2(config)#interface serial 1/0

R-2(config-if)#ip address 121.10.10.11 255.0.0.0

R-2(config-if)#no sh

R-2(config-if)#exit

R-2(config)#interface serial 1/1

R-2(config-if)#ip address 5.0.0.1 255.0.0.0

R-2(config-if)#clock rate 72000

R-2(config-if)#no shutdown 

R-2(config-if)#exit


RIP Configuration on R-2:-

---------------------------

R-2(config)#router rip 

R-2(config-router)#network 5.0.0.0

R-2(config-router)#network 121.10.10.0


IP Configuration on R-3:-

--------------------------

Router(config)#hostname R-3

R-3(config)#interface serial 1/0

R-3(config-if)#ip address 5.0.0.2 255.0.0.0

R-3(config-if)#no shutdown 

R-3(config)#interface fastEthernet 0/0

R-3(config-if)#ip add

R-3(config-if)#ip address 50.0.0.1 255.0.0.0.

R-3(config-if)#exit


RIP Configuration on R-3:-

---------------------------

R-3(config)#router rip 

R-3(config-router)#network 50.0.0.0

R-3(config-router)#network 5.0.0.0


Dynamic_NAT Configuration on R-1:-

-----------------------------------

R-1(config)#access-list 1 permit 10.0.0.0 0.255.255.255

R-1(config)#ip nat pool abhishek 121.10.10.15 121.10.10.20 netmask 255.0.0.0

R-1(config)#ip nat inside source list 1 pool abhishek

R-1(config)#interface fastEthernet 0/0

R-1(config-if)#ip nat inside 

R-1(config)#interface serial 1/0

R-1(config-if)#ip nat outside 

Note:- Ping PC-1(10.0.0.2) & PC-2(10.0.0.3) from Server(50.0.0.2). Thereafter check the status of Dynamic_Nat.




Thanks & Regards
Abhishek Pathak
+91-9621134014
abhishek9621134014@outlook.com


No comments:

Post a Comment

Computer Hardware_(A+) & Operating System with Networking

Microprocessor Motherboard About Operating System Create Bootable Pen Drive via Command Map Network Drive File Transfer Protocol in Windows ...