Inter VLAN Routing

 




Everyone must use this link for Practical of Inter VLAN:)





Show the Port Status of Router's

---------------------------------



Assign the IP Address of Subinterface of FastEthernet 0/0.1

------------------------------------------------------------

Router(config)#interface fastEthernet 0/0.1

Router(config-subif)#encapsulation dot1Q 1

Router(config-subif)#ip address 192.168.1.1 255.255.255.0

Router(config-subif)#no shutdown

Router(config-subif)#ex


Assign the IP Address of Subinterface of FastEthernet 0/0.2

------------------------------------------------------------

Router(config)#interface fastEthernet 0/0.2

Router(config-subif)#encapsulation dot1Q 2

Router(config-subif)#ip address 192.168.2.1 255.255.255.0

Router(config-subif)#no shutdown

Router(config-subif)#ex


Assign the IP Address of Subinterface of FastEthernet 0/0.3

------------------------------------------------------------

Router(config)#interface fastEthernet 0/0.3

Router(config-subif)#encapsulation dot1Q 3

Router(config-subif)#ip address 192.168.3.1 255.255.255.0

Router(config-subif)#no shutdown

Router(config-subif)#ex


Assign the IP Address of Subinterface of FastEthernet 0/0.4

------------------------------------------------------------

Router(config)#interface fastEthernet 0/0.4

Router(config-subif)#encapsulation dot1Q 4

Router(config-subif)#ip address 192.168.4.1 255.255.255.0

Router(config-subif)#no shutdown

Router(config-subif)#ex


Assign the IP Address of Subinterface of FastEthernet 0/0.5

------------------------------------------------------------

Router(config)#interface fastEthernet 0/0.5

Router(config-subif)#encapsulation dot1Q 5

Router(config-subif)#ip address 192.168.5.1 255.255.255.0

Router(config-subif)#no shutdown

Router(config-subif)#ex


Show the Port Status of Router's (SubInterface Port Down Till Now)

-------------------------------------------------------------------


Activate all SubInterface Port of Router's

-------------------------------------------

Router(config)#interface fastEthernet 0/0

Router(config-if)#no shutdown



Show the Port Status of Router's After Activate

------------------------------------------------



Trunk Configuration on Switch Port of F0/1

-------------------------------------------

Switch(config)#interface fastEthernet 0/1

Switch(config-if)#switchport mode trunk


VLAN Configuration on Switch Port of F0/2

-------------------------------------------

Switch(config)#interface fastEthernet 0/2

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 1

Switch(config-if)#ex


VLAN Configuration on Switch Port of F0/3

------------------------------------------

Switch(config)#interface fastEthernet 0/3

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 2

Switch(config-if)#ex


VLAN Configuration on Switch Port of F0/4

------------------------------------------

Switch(config)#interface fastEthernet 0/4

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 3

Switch(config-if)#ex


VLAN Configuration on Switch Port of F0/5

------------------------------------------

Switch(config)#interface fastEthernet 0/5

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 4

Switch(config-if)#ex


VLAN Configuration on Switch Port of F0/6

------------------------------------------

Switch(config)#interface fastEthernet 0/6

Switch(config-if)#switchport mode access

Switch(config-if)#switchport access vlan 5

Switch(config-if)#ex



Thanks & Regards
Abhishek Pathak
+91-9621134014

abhishek9621134014@outlook.com

No comments:

Post a Comment

Computer Hardware_(A+) & Operating System with Networking

Microprocessor Motherboard About Operating System Create Bootable Pen Drive via Command Map Network Drive File Transfer Protocol in Windows ...